Lancer Register Forum banner

Many Various Parts etc

4348 Views 57 Replies 21 Participants Last post by  Sider
All prices are collected from Leeds, West Yorkshire. Make me an offer.

Block cradle
Flywheel
Standard short engine, used but good
Complete head with cams, Mivec pulleys, some pipes and thermostat housing etc
Trigger wheel, front pulley, starter motor, cam cover, timing chain case
Oil pump, alternator, power steering and air con pumps, sump, various pipes and brackets
Standard exhaust manifold, standard turbo
In theory most of the parts, above, to build a complete engine with some ancillaries etc. Ideally sell as a job lot £1850, will entertain parts if enough interest.

Long engine, complete with most outer parts, suit a rebuild project (crate engine) £1800

Used Cosworth parts, crank, ISF polished and cryogenic treated, complete ported cylinder head, con. rods and camshafts £SOLD

Cosworth fuel injector rail £SOLD

ETS 4" bar core intercooler £SOLD

Koyo radiator (water) KV032037R £140

Carbon propshaft (suit GSR, not RS) £SOLD

Complete set Ohlins DFV c/w top mounts etc £SOLD

Complete set standard used Bilstein suspension with Tein lowering springs (will separate)

Pair Exe-tc adjustable top mounts (front) £50

Ross Sport swirl tank c/w Bosch 044 fuel pump etc (good for 600bhp) £220

Set of 4 ID 1000 fuel injectors £SOLD

3" air inlet pipe c/w maf housing and cone air filter £SOLD

AP Racing brake set front and rear (discs cryogenic treated) with XP10 pads, 2 spare front discs and 1 new disc (cryogenic treated) £SOLD

Full Milltek de-cat. exhaust with 5" slash cut outlets £SOLD

Powerflex 10Z75 front wishbone front bushes BNIB £12

Blox roll stopper BNIB £50

Mishimoto additional oil cooler (MMOC-EVO-08) BNIB £SOLD

Timing chain (Mitsubishi MN183896) cryogenic treated BNIB
Oil chain (Mitsubishi 1140A073) cryogenic treated BNIB £SOLD (for the pair)

K-MAC full race adjustable camber mountings BNIB £180

HKS Super Hybrid air filter BNIB £SOLD

Pair of Depo front fog lights BNIB £50

Pair of used gen :mitsi: front fog lights c/w mounting surround etc. £60

Carbon slam/ cooling panel £SOLD

Carbon engine cover, Rexpeed, OEM style £SOLD

Carbon wing vents (new) Rexpeed £SOLD

Carbon brake cooling ducts c/w mounting brackets (new) Rexpeed £110

AYC service/ bleed tool £90

South Side Performance (SSP) bumper mounting catch tank and pipes. Texas race series £160

MAP REV3 Inlet manifold with ceramic heat coating £SOLD

Standard boot spoiler Phantom Black £SOLD

CBRD BBX full turbo, fully overhauled and unused since £900

CBRD tubular TS exhaust manifold with heat coating £SOLD

Genuine Bride seat on Bride X specific sub frame (drivers side) £380

Evo X steering wheel, re-trimmed in Alcantara with blue, unused. £SOLD

Whiteline adjustable anti roll bar set, front and rear
Whiteline adjustable rear bottom arms £SOLD (will split see thread with pics HERE )

Forge BoV £SOLD see thread HERE Will also fit earlier cars.

Transfer box, fully rebuilt, upgraded, ISF polished and cryogenic treated by CliveW, unused since £SOLD

5 MT gearbox, fully rebuilt, upgraded, ISF polished and cryogenic treated by CliveW, unused since £SOLD

Owen Developments MHI billet turbo with ceramic ball bearing and metal cage core upgrade and shaft speed sensor ready. (Completed one track day and mapping time only) Always mapped with the speed sensor so kept with recommended limits. Covered approx 220 miles £1525 (Speed sensor equipment available)

MAP Investment cast exhaust manifold with ceramic heat coating £490

MoTeC M800 ecu with datalogging, advanced functions and knock control upgrades. Knock control board added £SOLD
(MoTeC C125 race dash, expander and sensors available separately)

Contact by PM or post up on here
Email [email protected]
See less See more
1 - 20 of 58 Posts
Sider what are the dfv for Evo wise?

Any pictures of the cooler? Both on and off the car?
Sider what are the dfv for Evo wise?

Any pictures of the cooler? Both on and off the car?
Everything in that list is for Evo X :smthumbup
AqWddccv. qQccccc


Sent from my iPhone using Tapatalk
Parts

3" air inlet pipe c/w maf housing and cone air filter £50

Can I have this please.

Thanks
Kev :smthumbup
Some great parts and prices you have there.
I'll take the timing chains Chris. What's the benefits of the cryogenic treatment?

What's condition of oil pump?

Davie
Some great parts and prices you have there.
Get the trailer hitched up, come get some bargains! :):smthumbup:D
Get the trailer hitched up, come get some bargains! :):smthumbup:D
:lol:
I've already got a number of these parts already fitted. Can't see them hanging about long.
:lol:
I've already got a number of these parts already fitted. Can't see them hanging about long.
You can always have spares cam :)
You can always have spares cam :)
Haha, If I had the money, it would be tempting.
You can always have spares cam :)
You not treating "The Mrs Evo" to a few more upgrades :mhihi:
  • Like
Reactions: 1
Would it be possible to get pictures of the brakes and are they floating discs? Just as wondering if they’ll fit the 9
You not treating "The Mrs Evo" to a few more upgrades :mhihi:
Maybe :) I am not telling you, as you would tell her :handsup:
  • Like
Reactions: 1
Maybe :) I am not telling you, as you would tell her :handsup:
I'm sure she'd spot them anyway like your other subtle purchases...... (ginormous tool box, massive wheels and tyres for your track etc)
Would it be possible to get pictures of the brakes and are they floating discs? Just as wondering if they'll fit the 9
Google is your friend! see HERE for a picture of the kit, yes they are floating discs :smthumbup
Carbon wing vents (new) Rexpeed. I will take these if still available
Carbon wing vents (new) Rexpeed. I will take these if still available
Yes they are still available :smthumbup
PM me your details and if you're collecting or wanting them posting :smthumbup
Adjustable Top Mounts.

Hi again
Can I take these too. Let me know postage.
Cheers
Kev :smthumbup
1 - 20 of 58 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top