Lancer Register Forum banner

Many Various Parts etc

6K views 57 replies 21 participants last post by  Sider 
#1 · (Edited)
All prices are collected from Leeds, West Yorkshire. Make me an offer.

Block cradle
Flywheel
Standard short engine, used but good
Complete head with cams, Mivec pulleys, some pipes and thermostat housing etc
Trigger wheel, front pulley, starter motor, cam cover, timing chain case
Oil pump, alternator, power steering and air con pumps, sump, various pipes and brackets
Standard exhaust manifold, standard turbo
In theory most of the parts, above, to build a complete engine with some ancillaries etc. Ideally sell as a job lot £1850, will entertain parts if enough interest.

Long engine, complete with most outer parts, suit a rebuild project (crate engine) £1800

Used Cosworth parts, crank, ISF polished and cryogenic treated, complete ported cylinder head, con. rods and camshafts £SOLD

Cosworth fuel injector rail £SOLD

ETS 4" bar core intercooler £SOLD

Koyo radiator (water) KV032037R £140

Carbon propshaft (suit GSR, not RS) £SOLD

Complete set Ohlins DFV c/w top mounts etc £SOLD

Complete set standard used Bilstein suspension with Tein lowering springs (will separate)

Pair Exe-tc adjustable top mounts (front) £50

Ross Sport swirl tank c/w Bosch 044 fuel pump etc (good for 600bhp) £220

Set of 4 ID 1000 fuel injectors £SOLD

3" air inlet pipe c/w maf housing and cone air filter £SOLD

AP Racing brake set front and rear (discs cryogenic treated) with XP10 pads, 2 spare front discs and 1 new disc (cryogenic treated) £SOLD

Full Milltek de-cat. exhaust with 5" slash cut outlets £SOLD

Powerflex 10Z75 front wishbone front bushes BNIB £12

Blox roll stopper BNIB £50

Mishimoto additional oil cooler (MMOC-EVO-08) BNIB £SOLD

Timing chain (Mitsubishi MN183896) cryogenic treated BNIB
Oil chain (Mitsubishi 1140A073) cryogenic treated BNIB £SOLD (for the pair)

K-MAC full race adjustable camber mountings BNIB £180

HKS Super Hybrid air filter BNIB £SOLD

Pair of Depo front fog lights BNIB £50

Pair of used gen :mitsi: front fog lights c/w mounting surround etc. £60

Carbon slam/ cooling panel £SOLD

Carbon engine cover, Rexpeed, OEM style £SOLD

Carbon wing vents (new) Rexpeed £SOLD

Carbon brake cooling ducts c/w mounting brackets (new) Rexpeed £110

AYC service/ bleed tool £90

South Side Performance (SSP) bumper mounting catch tank and pipes. Texas race series £160

MAP REV3 Inlet manifold with ceramic heat coating £SOLD

Standard boot spoiler Phantom Black £SOLD

CBRD BBX full turbo, fully overhauled and unused since £900

CBRD tubular TS exhaust manifold with heat coating £SOLD

Genuine Bride seat on Bride X specific sub frame (drivers side) £380

Evo X steering wheel, re-trimmed in Alcantara with blue, unused. £SOLD

Whiteline adjustable anti roll bar set, front and rear
Whiteline adjustable rear bottom arms £SOLD (will split see thread with pics HERE )

Forge BoV £SOLD see thread HERE Will also fit earlier cars.

Transfer box, fully rebuilt, upgraded, ISF polished and cryogenic treated by CliveW, unused since £SOLD

5 MT gearbox, fully rebuilt, upgraded, ISF polished and cryogenic treated by CliveW, unused since £SOLD

Owen Developments MHI billet turbo with ceramic ball bearing and metal cage core upgrade and shaft speed sensor ready. (Completed one track day and mapping time only) Always mapped with the speed sensor so kept with recommended limits. Covered approx 220 miles £1525 (Speed sensor equipment available)

MAP Investment cast exhaust manifold with ceramic heat coating £490

MoTeC M800 ecu with datalogging, advanced functions and knock control upgrades. Knock control board added £SOLD
(MoTeC C125 race dash, expander and sensors available separately)

Contact by PM or post up on here
Email sidermlr@gmail.com
 
See less See more
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top