AIM MXL wiring for Evo VIII fuel gauge sender - Mitsubishi Lancer Register Forum
 
 

Go Back   Mitsubishi Lancer Register Forum > Technical > Electrical / Security / ICE / Navigation

Reply
 
Thread Tools Rate Thread Display Modes
Old 18-05-2016, 18:28   #1
cra1g.b
User
 
cra1g.b's Avatar
 
Join Date: Aug 2011
Location: Aberdeenshire
Car: Norris Designs Evo VIII MR RS
Posts: 47
AIM MXL wiring for Evo VIII fuel gauge sender

Installing MXL dash into my Evo VIII, want to input fuel gauge sender to an analogue channel, but need to convert resistance to voltage as far as i'm aware, has anyone previously done this, and if so what resistors and dash settings did they use?

Have read that a pull up resistor is required in the circuit?

Also does anyone have a pinout for the original Evo VIII instrument cluster connectors?

Any useful advice would be appreciated

Thanks
cra1g.b is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 18-05-2016, 20:23   #2
Sir Marcus
Senior User
 
Sir Marcus's Avatar
 
Join Date: Oct 2005
Location: North Yorkshire.
Car: Evo 6 RS Sprint, JAM 2.3, AMS GT850R
My Car
Posts: 650
Yep, will dig out the info for wiring when back at home & post it up for ya
Sir Marcus is offline   Reply With Quote
The Following User Says Thank You to Sir Marcus For This Useful Post:
cra1g.b (18-05-2016)
Old 19-05-2016, 20:27   #3
Sir Marcus
Senior User
 
Sir Marcus's Avatar
 
Join Date: Oct 2005
Location: North Yorkshire.
Car: Evo 6 RS Sprint, JAM 2.3, AMS GT850R
My Car
Posts: 650
Here ya go, any questions mate, just post on this thread
The wiring is for an Evo 6 dash...
For an Evo 8, the fuel level wire is Green on C108(dash connector behind speedo) pin51 (the end pin)




Last edited by Sir Marcus; 26-10-2018 at 14:59..
Sir Marcus is offline   Reply With Quote
The Following 3 Users Say Thank You to Sir Marcus For This Useful Post:
carpe (22-08-2020), cra1g.b (23-05-2016), river evo 6 (19-05-2016)
Sponsored Links
Advertisement
 
Old 22-08-2020, 03:20   #4
carpe
Registered User
 
carpe's Avatar
 
Join Date: Oct 2005
My Car
Posts: 94
Hi sorry to dig up an old thread, what did you do for the Speedo wiring?

Thanks
carpe is offline   Reply With Quote
Old 22-08-2020, 12:55   #5
Sir Marcus
Senior User
 
Sir Marcus's Avatar
 
Join Date: Oct 2005
Location: North Yorkshire.
Car: Evo 6 RS Sprint, JAM 2.3, AMS GT850R
My Car
Posts: 650
No wiring required for the speedo as it takes the speed from the ECU over the serial cable RS232
Sir Marcus is offline   Reply With Quote
Old 22-08-2020, 13:23   #6
carpe
Registered User
 
carpe's Avatar
 
Join Date: Oct 2005
My Car
Posts: 94
Thank you for the reply.

After fitting the Link MXS Iíve lost the speed signal to the engine ECU, looks like terminal 51 of the combination meter needs a 12v supply.

Just wondered if you had the same issue?


Name:  IMG_4299.jpg
Views: 123
Size:  2.89 MB


Sent from my iPhone using Tapatalk
carpe is offline   Reply With Quote
Mitsubishi Lancer Register
Sponsored Links
Advertisement
 
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT. The time now is 10:36.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.