Rod job turbo choice ???? - Page 2 - Mitsubishi Lancer Register Forum
 
 

Go Back   Mitsubishi Lancer Register Forum > Technical > Engine / Turbo

Reply
 
Thread Tools Rate Thread Display Modes
Old 03-08-2019, 20:56   #16
Humps85
Senior User
 
Join Date: Jun 2017
Posts: 197
Quote:
Originally Posted by Goginawa View Post
What are you going to use the car for?
Iíve had rod job on my old 9 and has reworked 80 series. That thing was spooling like mad! Lasted only a year. If itís done properly itís fun. Iíve also heard 7460 is good turbo as long as you donít try to find its maximum. Keep it under whatís recommended and enjoy it
Fast road and a weekend toy, very much doubt I will take it to the track. What was the issue with the hybrid ??? Did you give it some hammer ?
Humps85 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 03-08-2019, 20:57   #17
Evo6er
Senior User
 
Evo6er's Avatar
 
Join Date: Mar 2009
Location: Kent
Car: EVO 8 MR
My Car
Posts: 3,242
Quote:
Originally Posted by Humps85 View Post
Fast road and a weekend toy, very much doubt I will take it to the track.

Hybrid FTW then




Sent from my iPhone using Tapatalk
__________________
Instagram @palmaredevo
Evo6er is offline   Reply With Quote
Old 03-08-2019, 21:16   #18
Goginawa
Zero Fighter
 
Goginawa's Avatar
 
Join Date: Jan 2010
Location: London
Car: EVO IX FQ 320
My Car
Posts: 12,576
Quote:
Originally Posted by Humps85 View Post
Fast road and a weekend toy, very much doubt I will take it to the track. What was the issue with the hybrid ??? Did you give it some hammer ?
There was a shaft play. Not sure what happened, if anything went into it or works wasnít that great. It was brilliant while it lasted. Made 480/440 at 1.8 bar. But it was engine out job, was fully blueprinted. And that was without aftermarket cams too
__________________
MAPPED BY ORACLE
evoless ,now something on a different Note
Goginawa is offline   Reply With Quote
Old 03-08-2019, 21:20   #19
Humps85
Senior User
 
Join Date: Jun 2017
Posts: 197
Quote:
Originally Posted by Goginawa View Post
There was a shaft play. Not sure what happened, if anything went into it or works wasnít that great. It was brilliant while it lasted. Made 480/440 at 1.8 bar. But it was engine out job, was fully blueprinted. And that was without aftermarket cams too
Who did the hybrid conversion ?
Humps85 is offline   Reply With Quote
Old 03-08-2019, 23:36   #20
Goginawa
Zero Fighter
 
Goginawa's Avatar
 
Join Date: Jan 2010
Location: London
Car: EVO IX FQ 320
My Car
Posts: 12,576
Quote:
Originally Posted by Humps85 View Post
Who did the hybrid conversion ?
Turbo was Done by race tech. There was other issues which might have cause the play in shaft. Itís anyones guess really. It was years ago, have put that behind now
__________________
MAPPED BY ORACLE
evoless ,now something on a different Note
Goginawa is offline   Reply With Quote
The Following User Says Thank You to Goginawa For This Useful Post:
Humps85 (04-08-2019)
Old 04-08-2019, 08:33   #21
kikiturbo
Senior User
 
Join Date: Feb 2008
Location: Croatia
Car: EVO 9 GSR
My Car
Posts: 2,609
Quote:
Originally Posted by da View Post
Is it faster spooling than the stock gt/rs turbo?
boost threshold is about the same as stock but transient response is much faster
kikiturbo is offline   Reply With Quote
The Following User Says Thank You to kikiturbo For This Useful Post:
da (08-08-2019)
Old 04-08-2019, 14:25   #22
strange_days_uk
Simon - EVO V
 
strange_days_uk's Avatar
 
Join Date: Feb 2016
Car: EVO V
My Car
Posts: 1,773
Rod job turbo choice ????

Had s205b on my stroker build, over 500 bhp but laggy.

Swapped to Owens HTA turbo and awesome spool and more power.
__________________
http://www.ap-tuning.co.uk/

Quote:
Originally Posted by Aidy View Post
Most TME owners have never driven an evo, including their own.
strange_days_uk is offline   Reply With Quote
Old 04-08-2019, 15:03   #23
Humps85
Senior User
 
Join Date: Jun 2017
Posts: 197
Quote:
Originally Posted by strange_days_uk View Post
Had s205b on my stroker build, over 500 bhp but laggy.

Swapped to Owens HTA turbo and awesome spool and more power.
Owens full frame kit ?
Humps85 is offline   Reply With Quote
Old 05-08-2019, 19:50   #24
Humps85
Senior User
 
Join Date: Jun 2017
Posts: 197
Quote:
Originally Posted by mlau1294 View Post
So I also have a rod-jobbed IX with similar upgrades as you have listed.

I firstly went with a S205b which got me close to 500bhp. The car went like stink when on boost but tbh was too laggy, I ended up having to learn to drive one gear lower all the time.

Anyway, I blew that turbo up (), so was in a similar situation as to what you are now:

Refit the s205b (as TT replaced my blown up one FOC)
Refit 80 series which I had taken off
Buy something new, like HKS Kai

So after some research I decided to sell the s205b and then upgrade my 80 series to the 20g. I didnít really want to spend £2k+ on the HKS at thatís particular time.

Iím rather pleased with the hybrid 80 series, on the same spec as I was with the S205b Iím now 470bhp and 465ftlb torque and car goes very well, not like the s205b on boost but quite close but much more driveable, and the high torque helps a lot. Itís slightly slower to spool over OEM 80 series (maybe ~300rpm) though.

Iíve thought about going for the HKS but for some better transient response and maybe more OEM spool, Iím not sure itís worth the ~£3k the new GTIII version of the HKS would likely be...

If you want 500+ then the HPB IX would be my choice (as a stock frame turbo), but I personally think high 400ís is as good as you can get for these cars in terms of power and everyday driveability...
What boost are you running the hybrid at for your bhp and torque ?
Humps85 is offline   Reply With Quote
Old 05-08-2019, 20:34   #25
mlau1294
Senior User
 
mlau1294's Avatar
 
Join Date: Jul 2012
Location: Alsace Region, France
Car: Blue Evo 9 (470/465), White 6RS (350/340) & Black Lancer GSR Ralliart Sportback (300/310)
My Car
Posts: 2,734
Quote:
Originally Posted by Humps85 View Post
What boost are you running the hybrid at for your bhp and torque ?
Just under 1.7 bar
mlau1294 is offline   Reply With Quote
The Following User Says Thank You to mlau1294 For This Useful Post:
Humps85 (05-08-2019)
Old 06-08-2019, 10:04   #26
strange_days_uk
Simon - EVO V
 
strange_days_uk's Avatar
 
Join Date: Feb 2016
Car: EVO V
My Car
Posts: 1,773
Quote:
Originally Posted by Humps85 View Post
Owens full frame kit ?
What is full frame? Mine is vband with tubular manifold.
__________________
http://www.ap-tuning.co.uk/

Quote:
Originally Posted by Aidy View Post
Most TME owners have never driven an evo, including their own.
strange_days_uk is offline   Reply With Quote
Old 13-08-2019, 17:37   #27
AlexGJ248
Senior User
 
AlexGJ248's Avatar
 
Join Date: Jun 2017
Location: Cheshire/Liverpool
Car: Evo 9 GT 474 bhp and 400 ft/lbs
Posts: 101
I've got very similar mods to you but I'm running an FP red BB making 474bhp and 400ftlbs at 2 bar (on standard cams). I've done nearly 10k miles on this set up with many sprints/hillclimbs and (touch wood) it's a great setup. I was told that the map is conservative and I could get 20-30bhp if I had it mapped on a rolling road.
__________________
474 bhp and 400 ft/lbs
AlexGJ248 is offline   Reply With Quote
The Following User Says Thank You to AlexGJ248 For This Useful Post:
Humps85 (13-08-2019)
Old 15-08-2019, 20:04   #28
barneyboo
Senior User
 
Join Date: Nov 2007
Posts: 2,982
Norris designs gen 2 full frame job done

Last edited by barneyboo; 15-08-2019 at 20:05..
barneyboo is offline   Reply With Quote
Old 15-08-2019, 22:04   #29
david_smith_909
Senior User
 
Join Date: Jun 2014
Location: North Wales
Car: E6
Posts: 168
If I had an Evo I'd still go with rods and hks

Sent from my Pixel 2 using Tapatalk
__________________
VI GSR
david_smith_909 is offline   Reply With Quote
Mitsubishi Lancer Register
Sponsored Links
Advertisement
 
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT. The time now is 05:54.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.