My X mapped @HQ - Mitsubishi Lancer Register Forum
 
 

Go Back   Mitsubishi Lancer Register Forum > Technical > ECU / Mapping

Reply
 
Thread Tools Rate Thread Display Modes
Old 14-07-2016, 22:06   #1
TurboShandy
Senior User
 
TurboShandy's Avatar
 
Join Date: Apr 2016
My Car
Posts: 134
My X mapped @HQ

So had my Evo X mapped at HQ yesterday and can't thank Russ enough for his work. This man really knows what he's doing. Made a nice 380/380 @ 1.7bar
The car was a FQ300 SST and the difference now is unbelievable. Got that proper Evo feel again.



[IMG]https://uploads.tapatalk-cdn.com/20160714/97979d5d6a109debb07affb3bd986a8c.jpg

[/IMG]


Sent from my iPhone
TurboShandy is offline   Reply With Quote
The Following User Says Thank You to TurboShandy For This Useful Post:
Sponsored Links
Advertisement
 
Old 14-07-2016, 23:09   #2
liffy16
Senior User
 
liffy16's Avatar
 
Join Date: Dec 2014
Location: oswestry shropshire
Car: white tommi
My Car
Posts: 508
Nice one ! what supporting mods exhaust,filter? Got a 3 inch turbo back milltek to go on mine hope for similar figures
__________________
I'm so skint i've got a kid in africa sending me money!
liffy16 is offline   Reply With Quote
Old 15-07-2016, 07:50   #3
TurboShandy
Senior User
 
TurboShandy's Avatar
 
Join Date: Apr 2016
My Car
Posts: 134
Quote:
Originally Posted by liffy16 View Post
Nice one ! what supporting mods exhaust,filter? Got a 3 inch turbo back milltek to go on mine hope for similar figures


I'v a 3" Milltek cat back with C-Tec decat and K&N typhoon with hard pipe kit. Was going to fit a 3 port boost solenoid but the standard one was holding nearly 2bar so wasn't required. We had too remove and flash the ecu though as it was locked to ECU tech.
TurboShandy is offline   Reply With Quote
The Following User Says Thank You to TurboShandy For This Useful Post:
liffy16 (18-07-2016)
Sponsored Links
Advertisement
 
Old 15-07-2016, 08:25   #4
OGA11Y
Senior User
 
OGA11Y's Avatar
 
Join Date: May 2015
Location: Aberdeenshire
Car: EVO X FQ300 SST
My Car
Posts: 216
Good results for the Mods!

I am sure i have seen your Reg on a S3??
__________________
OGA11Y is offline   Reply With Quote
Old 15-07-2016, 10:07   #5
[email protected] Performance
Registered User
 
Join Date: May 2016
Posts: 75
Thumbs up for Scottish Evo's and also Russ for being a top bloke!
David@ECK Performance is offline   Reply With Quote
The Following User Says Thank You to [email protected] Performance For This Useful Post:
davie-evo4 (15-07-2016)
Old 15-07-2016, 10:26   #6
muckyman
Registered User
 
Join Date: Jun 2009
Posts: 179
Quote:
Originally Posted by TurboShandy View Post
So had my Evo X mapped at HQ yesterday and can't thank Russ enough for his work. This man really knows what he's doing. Made a nice 380/380 @ 1.7bar
The car was a FQ300 SST and the difference now is unbelievable. Got that proper Evo feel again.


isn't it showing 280/280 on the graph?
muckyman is offline   Reply With Quote
Old 15-07-2016, 10:32   #7
stu's_evo
Registered User
 
Join Date: Sep 2012
Location: Hereford
Posts: 245
Quote:
Originally Posted by muckyman View Post
isn't it showing 280/280 on the graph?
Guessing thats at the wheel power and the 380/380 is flywheel power.
__________________
EVO 9 FQ360 - Forged engine, GT3076 HTA, FMIC, MOTEC M800, GSC Cams, Aeromotive 340LPH pump, RC 1000cc injectors, EXEEDY Twin plate, 5spd conversion, Profec B BC few other extras. IGT map 561/480
stu's_evo is offline   Reply With Quote
Old 15-07-2016, 10:39   #8
muckyman
Registered User
 
Join Date: Jun 2009
Posts: 179
Quote:
Originally Posted by stu's_evo View Post
Guessing thats at the wheel power and the 380/380 is flywheel power.
ahh, right - got it now
muckyman is offline   Reply With Quote
Old 15-07-2016, 11:35   #9
deannno
User
 
deannno's Avatar
 
Join Date: Mar 2016
My Car
Posts: 35
Nice figures! Russ is really a talented fella.

HQ gives figure printouts with ATW power.
deannno is offline   Reply With Quote
Old 15-07-2016, 11:50   #10
TurboShandy
Senior User
 
TurboShandy's Avatar
 
Join Date: Apr 2016
My Car
Posts: 134
Quote:
Originally Posted by OGA11Y View Post
Good results for the Mods!

I am sure i have seen your Reg on a S3??


Yea I had it on my S3 before this mate.



Sent from my iPhone
TurboShandy is offline   Reply With Quote
Old 15-07-2016, 11:54   #11
TurboShandy
Senior User
 
TurboShandy's Avatar
 
Join Date: Apr 2016
My Car
Posts: 134
Quote:
Originally Posted by deannno View Post
Nice figures! Russ is really a talented fella.

HQ gives figure printouts with ATW power.


He is without a doubt one of the best at what he does. Well worth the drive down there.


Sent from my iPhone
TurboShandy is offline   Reply With Quote
Old 15-07-2016, 11:56   #12
OGA11Y
Senior User
 
OGA11Y's Avatar
 
Join Date: May 2015
Location: Aberdeenshire
Car: EVO X FQ300 SST
My Car
Posts: 216
Quote:
Originally Posted by TurboShandy View Post
Yea I had it on my S3 before this mate.



Sent from my iPhone
I thought i had seen it going about before
__________________
OGA11Y is offline   Reply With Quote
Old 15-07-2016, 12:57   #13
davie-evo4
Regional Organiser
 
davie-evo4's Avatar
 
Join Date: Mar 2008
Location: glasgow
Car: A slow yin
My Car
Posts: 8,642
Good figures bud.

My 300 with only an exhaust change got 284/296 on HQ rollers.
__________________
"get the **** with it and make it ******* happen"

Tony Beets.....The Legend.
davie-evo4 is offline   Reply With Quote
Old 15-07-2016, 15:29   #14
TurboShandy
Senior User
 
TurboShandy's Avatar
 
Join Date: Apr 2016
My Car
Posts: 134
Quote:
Originally Posted by davie-evo4 View Post
Good figures bud.



My 300 with only an exhaust change got 284/296 on HQ rollers.


That's good numbers with just an exhaust, is yours a manual? I could have achieved more but didn't want to chance problems with the SST gearbox.


Sent from my iPhone
TurboShandy is offline   Reply With Quote
Mitsubishi Lancer Register
Sponsored Links
Advertisement
 
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT. The time now is 11:38.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.