Mitsubishi Lancer Register Forum - Search Results
 
 

Go Back   Mitsubishi Lancer Register Forum > Search Forums

Showing results 1 to 25 of 60
Search took 0.02 seconds.
Search: Posts Made By: donner
Forum: ECU / Mapping 12-03-2020, 19:01
Replies: 10
Views: 1,393
Posted By donner
Yes you can bench flash no issues. If you use jdm...

Yes you can bench flash no issues. If you use jdm IX rom (which I would prefer anyway), theres no need to disable EGR as it does not have it.
Forum: ECU / Mapping 19-01-2020, 16:06
Replies: 118
Views: 182,384
Posted By donner
Ok, if RS wiring is different it might not work....

Ok, if RS wiring is different it might not work. What I told is what I used in my 4.
Forum: ECU / Mapping 19-01-2020, 15:57
Replies: 118
Views: 182,384
Posted By donner
Leave 18 disconnected. E5 -> E9: 20 -> 30 ...

Leave 18 disconnected.

E5 -> E9:
20 -> 30
21 -> 31
Forum: ECU / Mapping 19-01-2020, 15:45
Replies: 118
Views: 182,384
Posted By donner
This works same way in case of IX ecu than 7/8...

This works same way in case of IX ecu than 7/8 ecu in 4-6, no difference in fan control. Do you have any old evoscan excel sheets showing how to set wirings when using 7/8 ecu in 4-6? Of course then...
Forum: ECU / Mapping 19-01-2020, 14:48
Replies: 118
Views: 182,384
Posted By donner
You are going to run mivec engine on earlier evo?...

You are going to run mivec engine on earlier evo?

I run IX ecu on my IV (not mivec yet) and it does not need fan controller.
Forum: Technical Questions 22-03-2019, 18:07
Replies: 4
Views: 519
Posted By donner
It's probably fuel pump and AC compressor pins...

It's probably fuel pump and AC compressor pins that needs to be cross swapped in case of E7 ecu. Otherwise ecu pin order should be the same, I have ran NA lancer with E8 ecu no problem.
Forum: Lancer Chat 08-12-2018, 16:47
Replies: 5
Views: 908
Posted By donner
They took measurements off evo block, made tools...

They took measurements off evo block, made tools and then just machined block to match evo block. I cant explain it better because I'm not machinist, I just found machinist who had enough interest to...
Forum: Lancer Chat 07-12-2018, 18:51
Replies: 5
Views: 908
Posted By donner
I use CS Lancer N/A block in my evo 4. It does...

I use CS Lancer N/A block in my evo 4. It does not have oil squirters but I had them machined and then block is the same than evo 5-7. If you check part numbers of engine internal parts, you will...
Forum: ECU / Mapping 05-12-2018, 14:44
Replies: 3
Views: 1,237
Posted By donner
Als air injection table is actually wrong name...

Als air injection table is actually wrong name for this 2d table, it is actually injector pulse width to control fueling during activated SAS control. But I'm afraid this only works in 88570008 evo 9...
Forum: ECU / Mapping 11-09-2018, 12:37
Replies: 3
Views: 1,369
Posted By donner
You need OP2.0 to flash your ACD ecu but you can...

You need OP2.0 to flash your ACD ecu but you can use 1.3 for datalogging.

C1 and K1 are quite different roms, C1 keeps center diff very open, has faster pressure reactions and suits best for...
Forum: Wanted 03-08-2018, 10:06
Replies: 2
Views: 187
Posted By donner
Evo 6 OZ center caps 4 pieces

I need Evo 6 OZ wheel center caps 4 pieces, original condition preferred. Evo 5 caps might be the same and those suit fine too. Thanks!
Forum: Engine / Turbo 02-07-2018, 05:48
Replies: 8
Views: 2,408
Posted By donner
Only way I can see it shortens pump life is...

Only way I can see it shortens pump life is because it can do acd clutch pressure changes faster or more often and then pump is turned on more often. But accu pressure itself is the same as in stock...
Forum: Technical Questions 20-05-2018, 19:13
Replies: 14
Views: 3,659
Posted By donner
No. Quite the opposite, center lock clamping...

No. Quite the opposite, center lock clamping force is about the same as in oem tarmac mode.
Forum: Engine / Turbo 20-05-2018, 18:58
Replies: 8
Views: 2,408
Posted By donner
Pump trigger points are untouched in Ralliart...

Pump trigger points are untouched in Ralliart roms. Its the same 11.8-15.2bar operating range for pump pressure.
Forum: ECU / Mapping 12-02-2018, 17:49
Replies: 3
Views: 458
Posted By donner
https://www.google.fi/url?sa=t&source=web&rct=j&ur...

https://www.google.fi/url?sa=t&source=web&rct=j&url=http://www.piilix.fi/manuals/VPV-MAP-EN.pdf&ved=2ahUKEwiRuqKnhaHZAhUI2ywKHcLnAboQFjACegQIDxAB&usg=AOvVaw198l0Y7_4rUENvFJQMbdPV
Forum: ECU / Mapping 09-02-2018, 13:12
Replies: 3
Views: 1,264
Posted By donner
If its obd2 then newer ecu helps.

If its obd2 then newer ecu helps.
Forum: ECU / Mapping 08-02-2018, 14:28
Replies: 3
Views: 1,264
Posted By donner
7-9 dont have CAN bus either. 7 and 8 260...

7-9 dont have CAN bus either.

7 and 8 260 ecu fits with few pin changes. 9 ecu can be done but need more work (conversion harness or new connectors crimped on old wires). I run 9 ecu in my 4 so...
Forum: Wanted 13-12-2017, 08:34
Replies: 3
Views: 822
Posted By donner
Yes some beams and cooling duct are reasonably...

Yes some beams and cooling duct are reasonably priced as new but meshes are expensive, thats why looking used ones first. 62046 is not available from Mitsubishi anymore, luckily others should be if...
Forum: Wanted 13-12-2017, 07:10
Replies: 3
Views: 822
Posted By donner
Evo 4 front bumper parts

For Evo 4 following front bumper related parts needed:
- all grille nets
- left hand side brake cooling duct
- fog light covers
- bumper support beams shown in picture below:
...
Forum: ECU / Mapping 30-11-2017, 11:00
Replies: 28
Views: 4,285
Posted By donner
Fred must mean 3d tables labeled as Knock Filter...

Fred must mean 3d tables labeled as Knock Filter or something like that, those are not knock control related.
Forum: ECU / Mapping 21-04-2017, 14:44
Replies: 17
Views: 1,302
Posted By donner
https://www.evolutionm.net/forums/ecuflash/693442-...

https://www.evolutionm.net/forums/ecuflash/693442-injector-flow-rate-linearization-table.html

There's something to add on your xml's.
Forum: ECU / Mapping 21-04-2017, 09:49
Replies: 17
Views: 1,302
Posted By donner
There is short pw adder table in stock ecu but...

There is short pw adder table in stock ecu but usually tuners dont bother and other thing is, this table is not very old found by disassemblers. In my opinion not needed with 1000cc or around, not...
Forum: ECU / Mapping 15-04-2017, 08:07
Replies: 13
Views: 2,085
Posted By donner
I have not experienced jitters on Ceddy rom, maf...

I have not experienced jitters on Ceddy rom, maf or sd, so I can't really help. Generally on sd jitters pay attention to map signal quality and analyze your problem with datalogging what there is...
Forum: ECU / Mapping 15-04-2017, 07:45
Replies: 13
Views: 2,085
Posted By donner
No effect on sd as map based load replaces this...

No effect on sd as map based load replaces this maf hz vs rpm based limited load. And even on maf your symptoms actually do not really fit how this table works but just mentioned this as there's no...
Forum: ECU / Mapping 15-04-2017, 04:41
Replies: 13
Views: 2,085
Posted By donner
One thing that might have effect on this is Ceddy...

One thing that might have effect on this is Ceddy disabled "maf Hz limit vs rpm" table and out of memory stock values in this table were lower than max value under 2000rpm. I have found this table...
Showing results 1 to 25 of 60
Mark All Forums Read

 
Forum Jump


All times are GMT. The time now is 13:38.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.