Mitsubishi Lancer Register Forum - Search Results
 
 
 
 

Go Back   Mitsubishi Lancer Register Forum > Search Forums
Reload this Page Search Results

Showing results 1 to 17 of 17
Search took 0.11 seconds. Search: Posts Made By: ThatGreyEvo8
Forum: Gearbox / Clutch / Transmission 18-05-2020, 16:47
Replies: 4
Views: 479
Posted By Steviej
You’ll need shifter, (handle), cables and gearbox...

You’ll need shifter, (handle), cables and gearbox mountings, I have a picture of everything that’s needed, if you want to message me a number or email I’ll send you it across.
Stevie
Forum: Gearbox / Clutch / Transmission 18-05-2020, 12:35
Replies: 4
Views: 479
Posted By super rover
if its a genuine 6rs box its likly to be VERY...

if its a genuine 6rs box its likly to be VERY shortly geared and only any good for around 120 mph ,cheak the numbers on it to see

i believe the linkage needs to be swopped
Forum: Engine / Turbo 28-04-2020, 17:47
Replies: 3
Views: 365
Posted By Ross W
Agree with Grant, the plain one is normally a...

Agree with Grant, the plain one is normally a good 'go to'. :thumbup:

Measure vac at idle and use attached chart

335235
Forum: Engine / Turbo 28-04-2020, 11:30
Replies: 3
Views: 365
Posted By Grant620
Usually the unpainted spring is fine. ...

Usually the unpainted spring is fine.
https://www.gb-ent.com/products/tial-q-50mm-bov-blow-off-valve-or-dump-valve?_pos=16&_sid=5645d644f&_ss=r
Forum: Engine / Turbo 28-04-2020, 10:36
Replies: 3
Views: 365
Posted By AlexEvo26
It really depends on how much vac your engine...

It really depends on how much vac your engine pulls, this may vary quite well depending on your configuration, especially cams.
Forum: Technical Questions 20-04-2020, 13:07
Replies: 2
Views: 395
Posted By Grant620
45mm should be fine on that turbo if you are...

45mm should be fine on that turbo if you are running decent boost yes.
Forum: Technical Questions 17-01-2020, 19:10
Replies: 2
Views: 419
Posted By Andy1986
Pretty sure once the bolts at the bottom are...

Pretty sure once the bolts at the bottom are removed it just slides upwards and then out. Been a while since I removed mine but from memory that's all it was.
Forum: Technical Questions 17-01-2020, 19:08
Replies: 2
Views: 419
Posted By Evo6er
https://uploads.tapatalk-cdn.com/20200117/157aa570...

https://uploads.tapatalk-cdn.com/20200117/157aa570f7293a4c2041b65689251531.jpg

Slide it up off the little hooks near the top


Sent from my iPhone using Tapatalk
Forum: Brakes 05-01-2020, 15:39
Replies: 14
Views: 1,992
Posted By TrickyDick
Simple answer yes :) What matters is the...

Simple answer yes :)

What matters is the direction of the inner cooling vanes. The direction shown below encourages air flow from inside to out for optimum cooling. Normally the grooves are cut in...
Forum: Brakes 05-01-2020, 07:54
Replies: 14
Views: 1,992
Posted By skinner6
I’ve ran 356 mm k sports under 17s before there...

I’ve ran 356 mm k sports under 17s before there snugged I give you that but do fit, btw I ran team dynamics these also clear that calliper too
Forum: Projects & Restorations 04-01-2020, 18:26
Replies: 9
Views: 1,148
Posted By jaiscossie
Very nice mate. How much were they out of interest

Very nice mate. How much were they out of interest
Forum: Projects & Restorations 04-01-2020, 18:12
Replies: 9
Views: 1,148
Posted By plip1953
Looking good :-) Pic re-sized to make it...

Looking good :-)

Pic re-sized to make it easier to view.
Forum: Brakes 04-01-2020, 12:24
Replies: 14
Views: 1,992
Posted By TrickyDick
That's impressive! Had to do some fettling on my...

That's impressive! Had to do some fettling on my Alcon 343mm setup to fit 17" Enkies.
Forum: Projects & Restorations 04-01-2020, 12:19
Replies: 9
Views: 1,148
Posted By plip1953
Any pics to show the amount of clearance?

Any pics to show the amount of clearance?
Forum: Wanted 26-10-2019, 22:06
Replies: 4
Views: 427
Posted By Eck8
This what your looking for? The car it was on...

This what your looking for? The car it was on made 650bhp


Sent from my iPhone using Tapatalk
Forum: ECU / Mapping 25-10-2019, 22:00
Replies: 4
Views: 713
Posted By ragz
1500 is way to high Mine sits at 950 to 1100 ...

1500 is way to high
Mine sits at 950 to 1100

Whoever mapped it should sort that
Forum: ECU / Mapping 25-10-2019, 20:42
Replies: 4
Views: 713
Posted By nplatenkamp
Hi, if they also mapped it, they should look into...

Hi, if they also mapped it, they should look into it.
Showing results 1 to 17 of 17

 
Forum Jump


All times are GMT. The time now is 03:48.

Contact Us - MLR - Archive - Top

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
 
Terms of Use
Copyright
Privacy Policy