pops n bangs [Archive] - Mitsubishi Lancer Register Forum

pops n bangs

evokev1985
06-04-2011, 13:00
hey guys how would i make my vii pop n bang?? got a full hks exhaust system hks filter and some other mods ecu mapped cars hitting almost 400bhp but no pops n bangs lol and cheep ideas :naughty:

Cupra r
06-04-2011, 13:08
you will need it mapped in and have a sas system and a decat too

AndyF_RSX
06-04-2011, 13:10
On VII's you also need to blank off the EGR system.

evokev1985
06-04-2011, 16:44
you will need it mapped in and have a sas system and a decat too

has full decat :smthumbup

evokev1985
06-04-2011, 16:45
On VII's you also need to blank off the EGR system.

where is the EGR system located? :shake:

grayw
06-04-2011, 16:53
EGR valve is below the throttle body, remove the valve and fit a blanking plate.

evokev1985
11-04-2011, 15:20
EGR valve is below the throttle body, remove the valve and fit a blanking plate.

removed EGR valve still no pops lol any ideas? :wallbang:

evokev1985
11-04-2011, 15:22
i take it u jst blank off the pipes that join onto egr valve when u remove it yeah? :confused:

Mark_RS
11-04-2011, 15:31
take the valve completly off and make a plate which blacks the whole thing off on the inlet manifold...

then the pops and bangs need mapping into the car.. very rare to do it by its self without it mapped in...

grayw
11-04-2011, 16:35
As above have you had them setup in the ECU?

ALAN CASSELLS
11-04-2011, 19:33
iv an e8 running 400 bhp but no pops and bangs, does the same apply, remove egr?

ALAN CASSELLS
11-04-2011, 20:10
any1 ever run a motec throttle kicker?

will2
11-04-2011, 20:12
:)had my pops n bangs all set up in alt map via auto cooler spray button ,but wasnt good ....blanked off egr,improved it ........... mapper then done few tweaks when i done some mods ....now its better than ever ..........+grayw advice always helps :smthumbup

ALAN CASSELLS
11-04-2011, 20:25
nice to see another member from ireland. any 1 any pics of egr blanked off?? what do you do with the vacuum pipe from egr valve?

gav_evo6
11-04-2011, 20:49
does anyone have any screen shots of the sas settings and how much -ign they are running in the lift off areas?

evokev1985
11-04-2011, 21:55
take the valve completly off and make a plate which blacks the whole thing off on the inlet manifold...

then the pops and bangs need mapping into the car.. very rare to do it by its self without it mapped in...

took it all off with a plate put in place il jst have to get in touch with mapper thx for the help guys :smthumbup

evokev1985
11-04-2011, 21:55
As above have you had them setup in the ECU?

:smthumbup

evokev1985
11-04-2011, 21:57
nice to see another member from ireland. any 1 any pics of egr blanked off?? what do you do with the vacuum pipe from egr valve?

blank the pipes off also :)

evokev1985
11-04-2011, 21:59
nice to see another member from ireland. any 1 any pics of egr blanked off?? what do you do with the vacuum pipe from egr valve?

also if u look in this link u will find a pic :smthumbup https://www.lancerregister.com/showthread.php?t=364668&highlight=egr+valve

will2
11-04-2011, 22:00
nice to see another member from ireland. any 1 any pics of egr blanked off?? what do you do with the vacuum pipe from egr valve?

where here in numbers you know :shake::crackup:https://www.lancerregister.com/showthread.php?t=366396&highlight=attention+irish

grayw
12-04-2011, 05:24
does anyone have any screen shots of the sas settings and how much -ign they are running in the lift off areas?

0 to 30 load and between 2500 and 7500 try around -20, if the SAS is set correctly, you should not need this anyhow.

KeithRann
12-04-2011, 06:46
I am not quite sure how mine was mapped by the previous owner at R-Spec but mine pops and bangs quite bloody loud without the ALS (pops and bangs) setting turned on!!!

grayw
12-04-2011, 12:16
I am not quite sure how mine was mapped by the previous owner at R-Spec but mine pops and bangs quite bloody loud without the ALS (pops and bangs) setting turned on!!!

One that Andy mapped then:lol:

AndyF_RSX
12-04-2011, 12:25
I like pops'n'bangs :flame:

Can't recall mapping any at R-Spec that were *too* noisy though :D

Andy

grayw
12-04-2011, 12:37
Must have been one of mine then:D

ALAN CASSELLS
12-04-2011, 12:44
Fancy mapping mine? :smthumbup

Gwigga
12-04-2011, 12:52
How can they be too noisey, the very fact there called pops and bangs!

AndyF_RSX
12-04-2011, 14:26
Fancy mapping mine? :smthumbup

R-spec mapping day coming up soon (https://www.lancerregister.com/showthread.php?t=367025)

Andy

KeithRann
12-04-2011, 14:27
Must have been one of mine then:D



So long as I know this is normal behaviour then. :crackup:

grayw
12-04-2011, 18:55
Yep if they asked for it:D